The 600-HP is a self-powered, high-output
subwoofer that may be used in both flown and
ground-stacked configurations. It is available
in three versions: as a portable version with
handles, for installation without handles, or
with rigging hardware. When fitted with the
optional QuickFly MRF-600 rigging frame, the
600-HP is designed to rig directly with the
MICA compact, high-power curvilinear array
loudspeakers. The versatility of the 600-HP
also allows it to be used with a variety of other
Meyer Sound self-powered loudspeakers —
including the CQ-1, CQ-2, UPA-1P, UPA-2P and
UPJ-1P — in fixed and touring applications.
The system features two specially designed
high-power 15-inch cone drivers, engineered
to provide optimal performance in subwoofer
applications. The high-excursion, back-vented
drivers have 4-inch voice coils, and each is
rated to handle 1200 watts (AES)*.
The two cone drivers are housed in a rectangular,
optimally tuned and vented enclosure that
is the same width as MICA, and a few inches
higher and deeper. The enclosure geometry
makes vertical ground-stacking easy and convenient.
All versions include plastic skids on
the bottom of the unit to prevent damage to
the enclosure or the unit below; the skids align
with slots on the cabinet’s top to ensure secure
stacking.Operating frequency range is from 36
Hz to 150 Hz, with a peak SPL at one meter of
138 dB.
Each cone driver is driven by a channel of the
integral two-channel class AB/H amplifier with
complementary MOSFET output stages. Total
output power is 2250 watts (4500 watts peak),
providing the system with sufficient headroom
to accommodate the most extreme sound reinforcement
demands with ease. The circuitry
includes TruPower® limiting to extend the
life of the drivers and hold long-term power
compression to less than 1 dB. The amplifier,
control electronics, and power supply are integrated
into a single, field-replaceable module
that is mounted into the rear of the enclosure.
The optional MRF-600 rigging frame uses
captive, rigid GuideALinks contained within
recessed guides in the lower front and rear
corners of the enclosure. A slot and convenient
pinned handle allow the link to be moved and
pinned for arraying or storage. The versatility
of angles achieved by using combinations of
subwoofer that may be used in both flown and
ground-stacked configurations. It is available
in three versions: as a portable version with
handles, for installation without handles, or
with rigging hardware. When fitted with the
optional QuickFly MRF-600 rigging frame, the
600-HP is designed to rig directly with the
MICA compact, high-power curvilinear array
loudspeakers. The versatility of the 600-HP
also allows it to be used with a variety of other
Meyer Sound self-powered loudspeakers —
including the CQ-1, CQ-2, UPA-1P, UPA-2P and
UPJ-1P — in fixed and touring applications.
The system features two specially designed
high-power 15-inch cone drivers, engineered
to provide optimal performance in subwoofer
applications. The high-excursion, back-vented
drivers have 4-inch voice coils, and each is
rated to handle 1200 watts (AES)*.
The two cone drivers are housed in a rectangular,
optimally tuned and vented enclosure that
is the same width as MICA, and a few inches
higher and deeper. The enclosure geometry
makes vertical ground-stacking easy and convenient.
All versions include plastic skids on
the bottom of the unit to prevent damage to
the enclosure or the unit below; the skids align
with slots on the cabinet’s top to ensure secure
stacking.Operating frequency range is from 36
Hz to 150 Hz, with a peak SPL at one meter of
138 dB.
Each cone driver is driven by a channel of the
integral two-channel class AB/H amplifier with
complementary MOSFET output stages. Total
output power is 2250 watts (4500 watts peak),
providing the system with sufficient headroom
to accommodate the most extreme sound reinforcement
demands with ease. The circuitry
includes TruPower® limiting to extend the
life of the drivers and hold long-term power
compression to less than 1 dB. The amplifier,
control electronics, and power supply are integrated
into a single, field-replaceable module
that is mounted into the rear of the enclosure.
The optional MRF-600 rigging frame uses
captive, rigid GuideALinks contained within
recessed guides in the lower front and rear
corners of the enclosure. A slot and convenient
pinned handle allow the link to be moved and
pinned for arraying or storage. The versatility
of angles achieved by using combinations of
front and back positions allows a MICA array
suspended under 600-HP subwoofers to be
uptilted for balcony coverage up to 15 degrees,
or downtilted to 6 degrees with respect to
the 600-HP. The 600-HP can make use of the
optional MG-MICA rigging grid to accommodate
a variety of flown and stacked configurations.
The durable enclosure is constructed of premium
birch plywood coated with a black, textured
hard-shell finish, with a powder-coated,
hex-stamped steel grille lined with acoustical
black mesh to protect the drivers. The exterior
dimensions of the 600-HP are suitable for both
European and U.S. trucks, and it can securely
travel in stacks using the MCF-MICA caster
frame, or MDB-600 dolly board when not fitted
with rigging frames.
Options for the 600-HP include weather protection
and custom color finishes for fixed
installations and other applications requiring
specific cosmetics. The RMS remote monitoring
system — standard with the rigging version
and optional with other configurations
— allows comprehensive monitoring of system
parameters on a Windows®-based network.
suspended under 600-HP subwoofers to be
uptilted for balcony coverage up to 15 degrees,
or downtilted to 6 degrees with respect to
the 600-HP. The 600-HP can make use of the
optional MG-MICA rigging grid to accommodate
a variety of flown and stacked configurations.
The durable enclosure is constructed of premium
birch plywood coated with a black, textured
hard-shell finish, with a powder-coated,
hex-stamped steel grille lined with acoustical
black mesh to protect the drivers. The exterior
dimensions of the 600-HP are suitable for both
European and U.S. trucks, and it can securely
travel in stacks using the MCF-MICA caster
frame, or MDB-600 dolly board when not fitted
with rigging frames.
Options for the 600-HP include weather protection
and custom color finishes for fixed
installations and other applications requiring
specific cosmetics. The RMS remote monitoring
system — standard with the rigging version
and optional with other configurations
— allows comprehensive monitoring of system
parameters on a Windows®-based network.
Datasheet Pdf
Operating Instructions Pdf